CST2466A/CST2466AE概述
CST2466A為攝像機、消費品、玩具和其他低電壓或電池驅動的應用提供集成電機驅動器控制。CST2466AE可提供高達1.8A的直流輸出電流。它使用2-11V的電機電源（VM）和2V-6V的設備電源（VCC），超低的RDS-on允許SOP-8包可用。CST2466A具有PWM（INA、INB）輸入接口。全套保護與過流保護、欠壓閉鎖和超溫停機相結合。峰值電流3.5A,CST2466A提供SOP-8和ESOP-8封裝。
The CST2466A provides an integrated motor driver for cameras, consumer products, toys and other application with low-voltage or battery-powered motion control.The CST2466AE can supply up to 1.8A of output DC current. It operates on a motor power supply (VM) from 2 to 11V and a device power supply voltage (VCC) of 2V to 6V. Ultra- low RDS-ON allows SOP-8 package available. The CST2466A has a PWM (INA、INB) input interface. Full protections are integrated with over-current protection, under-voltage lockout and over-temperature shutdown.
CST2466A/CST2466AE特性：
H橋電機驅動器
直流電機或其他負載
低導通電阻：280mΩ
1.8-A最大直流驅動電流
獨立電機和邏輯電源
電機VM:2至11V
邏輯VCC:2V至6V
低備用電流≤2uA/VM=VCC=5V
包裝和體積小
CST2466A提供SOP-8和ESOP-8封裝。
CST2466A提供SOP-8和ESOP-8封裝。
帶散熱片的ESOP-8封裝。
SOP-8封
保護特性
電流保護
電流保護
VCC欠壓閉鎖
熱保護
H-Bridge Motor Driver
DC Motor or Other Loads
Low On-Resistance : 280mΩ
1.8-A Maximum DC Drive Current
Separate Motor and Logic Supply
Motor VM : 2 to 11V
Logic VCC : 2V to 6V
Low-Stand-by Current ≤ 2uA/VM=VCC=5V
Small Package and Footprint
8-Pin ESOP with Thermal PAD
8-Pin SOP
Protection Features
VCC Under-voltage Lockout
Over-Current Protection
Thermal Shutdown
CST2466A/CST2466AE應用：
H-Bridge Motor Driver
DC Motor or Other Loads
Low On-Resistance : 280mΩ
1.8-A Maximum DC Drive Current
Separate Motor and Logic Supply
Motor VM : 2 to 11V
Logic VCC : 2V to 6V
Low-Stand-by Current ≤ 2uA/VM=VCC=5V
Small Package and Footprint
8-Pin ESOP with Thermal PAD
8-Pin SOP
Protection Features
VCC Under-voltage Lockout
Over-Current Protection
Thermal Shutdown
CST2466A/CST2466AE應用：
電動牙刷、電鎖
攝像機
單反鏡頭
消費品
玩具
機器人學
CST2466A/CST2466AE PCB布局指南：
CST2466A/CST2466AE PCB布局指南：
用圖.jpg)
The capacitor C1 connected between the GND and the VM pins must be located as close as possible to the CST2466A chip. In different applications, C1(show as above) is recommended to use a 0.1uF in 3V applications; a 1uF is recommended for 4.5V applications; a 4.7uF is recommended for 6V applications; in 9.6V applications, it is recommended to use 22uF, all these capacitors should be SMD package.The connection between the negative pole of the capacitor and the GND terminal of the IC should be as short as possible. That is to say, the line route should not far away.
When the application board has capacitors while filtering for other chips that is far away from the CST2466A, it need to place a small capacitor for CST2466A.
The capacitor C3 preferably soldering to the motor poles instead of placing it on the PCB. When it is inconvenient to soldering on the motor poles, it can be mount on the PCB. The following diagram is the PCB layout reference .
CST2466A/CST2466AE 管腳腳位圖：
CST2466A/CST2466AE 板圖：
CST2466A/CST2466AE 板圖：
發送郵件
商務QQ客服
13823761625
